لیست قیمت ماژول های ورودی/خروجی ای بی بی (ABB I/O Modules)

DO910N (D04)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area.DO910N Digital Output (DO4), output for intrinsically safe valves or alarms.
Features and benefits
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Output for intrinsically safe valves or alarms
• Integrated driving power
• Short and break detection
• Electrical isolation between output / bus and output / power
• Electrical isolation channel to channel
• 4 channels (do910nd04)

IP920

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
IP920 Module housing (Cover for empty slots in TU921S, B and N).
Features and benefits
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Hot Swap functionallity
• Cover for empty slots in TU921S, B and N (3KDE175831L9200)

AO930N (AO4H)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area.
AO930N Analog Output (AO4H), output signal 0/4…20 mA for actuators.
Features and benefits

Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionallity
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Output signal 0/4…20 mA for actuators
Short and break detection
Electrical isolation between output / bus and output / power
Output with common ground
4 channels
Transmission of HART frames via the fieldbus
Cyclic HART variables (3KDE175533L9300)

AO920N (AO4I)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.

S900 I/O type N. For installation in safe (= non-hazardous) area.
AO920N Analog Output (AO4I), output signal 0/4…20 mA for actuators.
Features and benefits
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Output signal 0/4…20 mA for actuators
– Short and break detection
– Electrical isolation between output / bus and output / power
– Electrical isolation channel to channel
– 4 channels (3KDE175533L9200)

AO910N (AO4)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area.
AO910N Analog Output (AO4), output signal 0/4…20 mA for actuators.
Features and benefits
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Output signal 0/4…20 mA for actuators
– Short and break detection
– Electrical isolation between output / bus and output / power
– Output with common ground
– 4 channels (3KDE175533L9100)

AO930B (AO4H-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AO930B Analog Output (AO4H-B), output signal 0/4…20 mA for actuators.
Features and benefits

ATEX Certification for installation in Zone 2
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionallity
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Output signal 0/4…20 mA for actuators
Short and break detection
Electrical isolation between output / bus and output / power
Output with common ground
4 channels
Transmission of HART frames via the fieldbus
Cyclic HART variables (3KDE175532L9300)

AO920B (AO4I-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.

AO920B Analog Output (AO4I-B), output signal 0/4…20 mA for actuators.
Features and benefits
– ATEX Certification for installation in Zone 2
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Output signal 0/4…20 mA for actuators
– Short and break detection
– Electrical isolation between output / bus and output / power
– Electrical isolation channel to channel
– 4 channels (3KDE175532L9200)

AO910B (AO4-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AO910B Analog Output (AO4-B), output signal 0/4…20 mA for actuators.

Features and benefits
– ATEX Certification for installation in Zone 2
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Output signal 0/4…20 mA for actuators
– Short and break detection
– Electrical isolation between output / bus and output / power
– Output with common ground
– 4 channels (3KDE175532L9100)

AO930S (AO4H-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AO930S Analog Output (AO4H-Ex), output signal 0/4…20 mA for actuators.
Features and benefits

ATEX Certification for installation in Zone 1
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionallity
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Output signal 0/4…20 mA for actuators
Short and break detection
Electrical isolation between output / bus and output / power
Output with common ground
4 channels
Transmission of HART frames via the fieldbus
Cyclic HART variables (3KDE175531L9300)

AO920S (AO4I-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AO920S Analog Output (AO4I-Ex), output signal 0/4…20 mA for actuators.
Features and benefits

ATEX Certification for installation in Zone 1
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionallity
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Output signal 0/4…20 mA for actuators
Short and break detection
Electrical isolation between output / bus and output / power
Electrical isolation channel to channel
4 channels (3KDE175531L9200)

AO910S (AO4-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.

AO910S Analog Output (AO4-Ex), output signal 0/4…20 mA for actuators.
Features and benefits
– ATEX Certification for installation in Zone 1
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Output signal 0/4…20 mA for actuators
– Short and break detection
– Electrical isolation between output / bus and output / power
– Output with common ground
– 4 channels (3KDE175531L9100)

AI950N (TI4)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.

S900 I/O type N. For installation in safe (= non-hazardous) area. AI950N Temperature Input (TI4), supporting Pt100, Pt1000 and Ni100 in 2-/3-/4-technology. Thermocouples B, E, J, K, L, N, R, S, T, U, mV. Isolated inputs channel by channel.
Features and benefits
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Pt 100, Pt 1000, Ni 100, 0…3kOhms in 2/3/4 wire technique
– Thermocouple Type B, E, J, K, L, N, R, S, T, U, mV
– Internal or external cold junction compensation
– Short and break detection
– Electrical isolation between input / bus and input / power
– Electrical isolation channel to channel
– 4 channels (3KDE175523L9500)

AI950B (TI4-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AI950B Temperature Input (TI4-B), supporting Pt100, Pt1000and Ni100 in 2-/3-/4- technology. Thermocouples B, E, J, K, L, N, R, S, T, U, mV. Isolated inputs channel by channel.
Features and benefits
– ATEX Certification for Zone 2
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Pt 100, Pt 1000, Ni 100, 0…3kOhms in 2/3/4 wire technique
– Thermocouple Type B, E, J, K, L, N, R, S, T, U, mV
– Internal or external cold junction compensation
– Short and break detection
– Electrical isolation between input / bus and input / power
– Electrical isolation channel to channel
– 4 channels (3KDE175522L9500)

AI950S (TI4-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AI950S Temperature Input (TI4-Ex), supporting Pt100, Pt1000 and Ni100 in 2-/3-/4-technology. Thermocouples type B, E, J, K, L, N, R, S, T, U, mV. Isolated inputs channel by channel.
Features and benefits
– ATEX Certification for installation in Zone 1
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Pt 100, Pt 1000, Ni 100, 0…3kOhms in 2/3/4 wire technique
– Thermocouple Type B, E, J, K, L, N, R, S, T, U, mV
– Internal or external cold junction compensation
– Short and break detection
– Electrical isolation between input / bus and input / power
– Electrical isolation channel to channel
– 4 channels (3KDE175521L9500)

AI931N (AI4H)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.S900 I/O type N. For installation in safe (= non-hazardous) area.AI931N Analog Input (AI4H), passive inputs for 0/4…20 mA.
Features and benefits
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Passive inputs for 0/4…20 mA
– Short and break detection
– Electrical isolation between input / bus and input / power
– Common return for all inputs
– 4 channels
– Transmission of HART frames via the fieldbus
– Cyclic HART variables (3KDE175513L9310)

AI930N (AI4H)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area.

AI930N Analog Input (AI4H), input and power supply for 4…20 mA loop powered 2-wire transmitters. 
Features and benefits
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics

-Power supply for 4…20 mA loop powered 2-wire transmitters

-Short and break detection

-Electrical isolation between input / bus and input / power

-Common return for all inputs

-4 channels

-Transmission of HART frames via the fieldbus

-Cyclic HART variables (3KDE175513L9300)

AI910N (AI4)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.S900 I/O type N. For installation in safe (= non-hazardous) area.
AI910N Analog Input (AI4), input and power supply for 4…20 mA loop powered 2-wire transmitters.
Features and benefits

Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionality
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Power supply for 4…20 mA loop powered 2-wire transmitters
Short and break detection
Electrical isolation between input / bus and input / power
Common return for all inputs
4 channels (3KDE175513L9100)

AI931B (AI4H-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AI931B Analog Input (AI4H-B), passive inputs for 0/4…20 mA.
Features and benefits
– ATEX Certification for installation in Zone 2
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Passive inputs for 0/4…20 mA
– Short and break detection
– Electrical isolation between input / bus and input / power
– Common return for all inputs
– 4 channels
– Transmission of HART frames via the fieldbus
– Cyclic HART variables (3KDE175512L9310)

AI930B (AI4H-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.

AI930B Analog Input (AI4H-B), input and power supply for 4…20 mA loop powered 2-wire transmitters.
Features and benefits
– ATEX Certification for installation in Zone 2
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Power supply for 4…20 mA loop powered 2-wire transmitters
– Short and break detection
– Electrical isolation between input / bus and input / power
– Common return for all inputs
4 channels
– Transmission of HART frames via the fieldbus
– Cyclic HART variables (3KDE175512L9300)

AI910B (AI4-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.

AI910B Analog Input (AI4-B), input and power supply for 4…20 mA loop powered 2-wire transmitters.
Features and benefits

ATEX Certification for Zone 2
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionality
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Power supply for 4…20 mA loop powered 2-wire transmitters
Short and break detection
Electrical isolation between input / bus and input / power
Common return for all inputs
4 channels (3KDE175512L9100)

AI931S (AI4H-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.

S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AI931S Analog Input (AI4H-Ex), passive inputs for 0/4…20 mA.
Features and benefits

– ATEX Certification for installation in Zone 1
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Passive inputs for 0/4…20 mA
– Short and break detection
– Electrical isolation between input / bus and input / power
– Common return for all inputs
– 4 channels
– Transmission of HART frames via the fieldbus
– Cyclic HART variables (3KDE175511L9310)

AI930S (AI4H-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AI930S Analog Input (AI4H-Ex), input and power supply for 4…20 mA loop powered 2-wire transmitters.
 
 
 

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant.

Features and benefits
– ATEX Certification for Zone 1
– Redundancy (Power and Communication)
– Hot Configuration in Run
– Hot Swap functionallity
– Extended Diagnostic
– Excellent configuration and diagnostics via FDT/DTM
– G3 – coating for all components
– Simplified maintenance with auto-diagnostics
– Power supply for 4…20 mA loop powered 2-wire transmitters
-Short and break detection
-Electrical isolation between input / bus and input / power
-Common return for all inputs
-4 channels
-Transmission of HART frames via the fieldbus
-Cyclic HART variables (3KDE175511L9300)

AI910S (AI4-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
AI910S Analog Input (AI4-Ex), input and power supply for 4…20 mA loop powered 2-wire transmitters.
Features and benefits

ATEX Certification for installation in Zone 1
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionality
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Power supply for 4…20 mA loop powered 2-wire transmitters
Short and break detection
Electrical isolation between input / bus and input / power
Common return for all inputs
4 channels (3KDE175511L9100)

DP910N (FI2)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area.
DP910N Frequency Input (FI2), frequency input for dry contacts or proximity switches.
Features and benefits
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
•
Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
•
Frequency input for dry contacts or proximity switches
• Short and break detection
• Electrical isolation between input / bus and input / power
• Frequency measurement or counting applications
• 2 Function blocks
• Reset via fieldbus or control input
• Status outputs / Direction recognition (3KDE175363L9100)

DP910B (FI2-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
DP910B Frequency Input (FI2-B), frequency input for dry contacts or proximity switches.
Features and benefits
• ATEX Certification for installation in Zone 2
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Frequency input for dry contacts or proximity switches
• Short and break detection
• Electrical isolation between input / bus and input / power
• Frequency measurement or counting applications
• 2 Function blocks
• Reset via fieldbus or control input
• Status outputs / Direction recognition (3KDE175362L9100)

DP910S (FI2-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
DP910S Frequency Input (FI2-Ex), frequency input for dry contacts or proximity switches.
Features and benefits
• ATEX Certification for installation in Zone 1
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Frequency input for dry contacts or proximity switches
• Short and break detection
• Electrical isolation between input / bus and input / power
• Frequency measurement or counting applications
• 2 Function blocks
• Reset via fieldbus or control input
• Status outputs / Direction recognition (3KDE175361L9100)

DO910B (D04-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
DO910B Digital Output (DO4-B), output for intrinsically safe valves or alarms.
Features and benefits
• ATEX Certification for installation in Zone 2
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Output for intrinsically safe valves or alarms
• Integrated driving power
• Short and break detection
• Electrical isolation between output / bus and output / power
• Electrical isolation channel to channel
• 4 channels (3KDE175322L9100)

DO910S (DO4-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.DO910S (DO4-Ex), output for Intrinsically safe valves or alarms.
Features and benefits
• ATEX Certification for installation in Zone 1
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Output for intrinsically safe valves or alarms
• Integrated driving power
• Short and break detection
• Electrical isolation between output / bus and output / power
• Electrical isolation channel to channel
• 4 channels (3KDE175321L9100)

DX910N (DIO8)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area.
DX910N Digital Input or Output (DI08), input for dry contacts or proximity switches, output for low power intrinsically safe valves.
Features and benefits
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Input for dry contacts or proximity switches (NAMUR)
• Output for low power intrinsically safe valves
• Short and break detection
• Electrical isolation between input / bus and input / power
• Common return for all inputs / outputs
• Configurable as a mixture of inputs and outputs
• 8 I/O channels (3KDE175313L9100)

DX910B (DIO8-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
DX910B Digital Input or Output (DI08-B), input for dry contacts or proximity switches, output for low power intrinsically safe valves.
Features and benefits
• ATEX Certification for installation in Zone 2
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Input for dry contacts or proximity switches (NAMUR)
• Output for low power intrinsically safe valves
• Short and break detection
• Electrical isolation between input / bus and input / power
• Common return for all inputs / outputs
• Configurable as a mixture of inputs and outputs
• 8 I/O channels (3KDE175312L9100)

DX910S (DIO8-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
DX910S Digital Input or Output (DI08-Ex), input for dry contacts or proximity switches, output for low power intrinsically safe valves.
Features and benefits

• ATEX Certification for installation in Zone 1
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Input for dry contacts or proximity switches (NAMUR)
• Output for low power intrinsically safe valves
• Short and break detection
• Electrical isolation between input / bus and input / power
• Common return for all inputs / outputs
• Configurable as a mixture of inputs and outputs
• 8 I/O channels (3KDE175311L9100)

TU921N RTU (TU16R)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.

S900 I/O type N. For installation in safe (= non-hazardous) area.
TU921N Redundant Termination Unit (TU16R), for 16 I/O-modules, redundant communication and power (Delivery includes CD910).
Features and benefits

For installation in safe areas (non-hazardous)
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionallity
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Mounting in safe area possible
Termination unit for up to 16 I/O modules
Prepared for redundant system power and communication
Up to 4 terminals per channel
Pre-selection of fieldbus address
Prepared for certified field housing
Mounting only in safe area possible (3KDE175113L9210)

TU921B RTU (TU16R-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.

TU921B Redundant Termination Unit (TU16R-B), for 16 I/O-modules, redundant communication and power (Delivery includes CD910).

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the Profibus DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.

Features and benefits

ATEX Certification for installation in Zone 2
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionallity
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Mounting in safe area or Zone 2 possible
Termination unit for up to 16 I/O modules
Prepared for redundant system power and communication
Up to 4 terminals per channel
Pre-selection of fieldbus address
Prepared for certified field housing
Mounting in Zone 2 or safe area possible (3KDE175112L9210)

TU921S RTU (TU16R-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.

TU921S Redundant Termination Unit (TU16R-Ex), for 16 I/O-modules, redundant communication and power (Delivery includes CD910).
Features and benefits

ATEX Certification for installation in Zone 1
Redundancy (Power and Communication)
Hot Configuration in Run
Hot Swap functionallity
Extended Diagnostic
Excellent configuration and diagnostics via FDT/DTM
G3 – coating for all components
Simplified maintenance with auto-diagnostics
Termination unit for up to 16 I/O modules
Prepared for redundant system power and communication
Up to 4 terminals per channel
Preselection of fieldbus address
Prepared for certified field housing
Mounting in Zone 1, Zone 2 or safe area possible (3KDE175111L9210)

DO814

The DO814 is a 16 channel 24 V digital output module with current sinking for the S800 I/O. The output voltage range is 10 to 30 volt and the maximum continuous current sinking is 0.5 A. The outputs are protected against short circuits and over temperature. The outputs are divided into two individually isolated groups with eight output channels and one voltage supervision input in each group.
Each output channel consists of a short circuit and over temperature protected low side switch, EMC protection components, inductive load suppression, output state indication LED and optical isolation barrier. The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read via the ModuleBus.
Features and benefits

16 channels for 24 V d.c. current sinking outputs
2 isolated groups of 8 channels with process voltage supervision
Output status indicators
OSP sets outputs to predetermined state upon error detection
Short-circuit protection to ground and 30 V
Over-voltage and over-temperature protection (3BUR001455R1)

DI814

The input voltage range is 18 to 30 volt dc and the input current source is 6 mA at 24 V. The inputs are divided into two individually isolated groups with eight channels and one voltage supervision input in each group. Every input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier. The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read through the ModuleBus.
Features and benefits

16 channels for 24 V d.c. inputs with current sourcing
2 Isolated groups of 8 with voltage supervision
Input status indicators (3BUR001454R1)

TL830 / TL831 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
TL830 and TL831 IP30 protection cover for power inlets on FCI base plate TU865/TU860. 20 pieces of TL830 and 10 pieces of TL831 per package.
 
Features and benefits

Protection cover for power inlets on FCI base plate TU865/TU860
Usable for enabling IP30 for the power supply connectors
Required in case that intrinsically safe Select I/O equipment is used together with an FCI in the same cabinet
TL830 has to be used to cover the power supply connector with any connected power supply cables
TL831 has to be used to cover the power supply connectors without connected power supply cables (3BSE093013R1)

TUW890 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.The TUW890 is a separator wall used in IS applications. Specifically, this wall is for added protection and placed between Select I/O MTUs having intrinsically safe SCMs and Select I/O MTUs that include non-IS SCMs. (10 pieces of TUW890 per package)
 
Features and benefits

IS Separator for I/O MTU (IS-wall)
Usable between I/O MTU with (blue) intrinsically safe and (grey) non-intrinsically safe FTB
Can be used in hazardous areas (3BSE093009R1)

FTB840K01 (Spare parts)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The FTB840 is a redundant terminal signal block with 4 screw terminals to be used with a redundant pair of Signal Conditioning Modules. The FTB is installed on the MTU for Select I/O (TUS810) and includes a keying mechanism that is set to a specific code when an SCM is first inserted to ensure only the same type of SCM can be installed in that slot. The key can be reset by removing and reinserting the FTB. (10 pieces per package)
 
Features and benefits

Two slots for connection of a redundant SCM pair
Four screw terminals for connection of wires
Coding system with 5 coding fingers for self-learning and resettable coding of the SCM type
Can be used in hazardous areas
Hole for each terminal for connecting test probes (for measurements) (3BSE093007R1)

GTS810 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The GTS810 Grounding Termination Module provides a ground termination alternative for field wires associated with a single Field Termination Block (FTB).
Features and benefits

Ground termination option for all field wires connected to the belonging FTB
Easy reconnection of field wiring when GTS810 will be replaced by an SCM
Mechanical keying to prevent insertion of wrong module type after commissioning
Can be used in hazardous areas
Usable for (blue) IS and (grey) non-IS FTB
No LED indicators (3BSE093006R1)

GFS810 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The GFS810 provides ground fault detection for signals with field supply sources from external power injection.
Features and benefits

Ground fault detection for signals with field supply sourced from external power injection.
Measuring of resistance to ground to provide it as an analog value to the application.
Can be used with all GIO module types (GIS810 and GIS880).
Galvanic isolation.
Diagnostics:

Line break supervision of ground connection.
Internal self test.
Test option for ground fault detection function (trough external button).
LED indicators on the SCM indicate the operational state of the module. (3BSE093005R1)

TUS810K02

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
The TUS810K02 Select I/O Modular Termination Unit (MTU), for Intrinsically safe (IS) applications, hosts Generic I/O modules (GIOs) and up to 16 Signal Conditioning Modules (SCMs) which completes a single I/O unit. When using the TUS810K02 for IS applications, the Power Injection Terminal Blocks are removed and replaced with empty slot protectors.
There is self-learning coding on the FTBs that gets set upon the initial insertion of an SCM so that if an SCM is replaced, only the same type of SCM can be inserted. To insert another type of SCM, the coding can be reset manually. The MTU also has a coding for the GIO, so that it can only be replaced with the same type of GIO.
TUS810K02 includes the DIN-rail mountable TUS810 MTU, 16 pcs FTB890 IS Field Termination Blocks, 2 pcs of TL820 Empty Slot Protectors and 1 pcs of TUC810 Terminal Cover.
Features and benefits

Two slots for connection of Generic I/O modules (GIO).
16 slots for connection of Signal Conditioning Modules (SCM).
For intrinsically safe usage, TL820 has to be inserted into the PTB slots (included in TUS810K02)
Two Modulebus connectors, one in and one out.
One slot for connection of a grounding bar (GTB).
DIN rail mounted. 2 locking devices to lock the MTU to the DIN rail.
Slots for screw lugs (optional, for harsh high vibration environment).
Can be used in hazardous areas
Prepared for intrinsically safe usage by the components included in TUS810K02

More info

More info

× (3BSE093004R1)

TB861V011 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
A cluster of up to 12 I/O units can be connected to one FCI. If they are all on the same DIN rail, the I/O MTUs are connected to each other. The Modulebus then goes though the I/O MTUs.
If not all the I/O MTUs can fit on the same DIN rail, TB861 can be used to extend the Modulebus to the first I/O MTU on the next DIN rail. The outlet part is connected to the bottom of the last I/O MTU on the first DIN rail. The inlet part is connected to the top of the first I/O MTU on the second DIN rail. TB861V011 extends the Modulebus from one DIN-rail to another. Length 1.1 m.
Features and benefits

Extends the Modulebus from one DIN-rail to another. Length 1.1 m.
Available in three lengths.
DIN rail mounted. 2 locking devices (one locks outlet to DIN rail and one locks inlet to DIN rail). (3BSE090352R1)

TS810K01 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
Screw lugs for TU860/TU865 and TUS810. 100 pieces per package.
Features and benefits

Screw lugs for TU860/TU865 and TUS810
Screw lugs are optional; for harsh vibration environment (3BSE090351R1)

PTB810K01 (Spare parts)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The PTB810K01 Power Injection Terminal Block Kit is used for the Select I/O Module Termination Unit (TUS810). Two PTB810s are needed per MTU. Digital output SCMs (DOS810, DOS880, DOS885) and high amp SCMs (DOS885, AIS885) require power injection. (10 pieces per package).
Features and benefits

Injects 24 V field power to high power SCMs on the MTU
Can provide up to 20 A.
Can be used in hazardous areas.
Hole for each terminal for connecting test probes (for measurements
Four screws for daisy chain option of the power supply (3BSE088182R1)

TUC810K01 (Spare parts)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
TUC810K01 an Terminal Cover Kit protects the field terminal blocks and holds wiring labels for the Select I/O TUS810K01 and TUS810K02 MTUs. (10 pieces per package).
Features and benefits

Terminal Cover which holds user labels for the Select I/O Module Termination Unit
Swiveling (3BSE088181R1)

FTB810K01 (Spare parts)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The FTB810 is a field terminal block with 4 screw terminals to be used with a single Signal Conditioning Module. The FTB is installed on the MTU for Select I/O (TUS810) and includes a keying mechanism that is set to a specific code when an SCM is first inserted to ensure only the same type of SCM can be installed in that slot. The key can be reset by removing and reinserting the FTB. (10 pieces per package)
 
Features and benefits

One slot for connection of SCM
Four screw terminals for connection of wires
Coding system with 5 coding fingers for self-learning and resettable coding of the SCM type
Can be used in hazardous areas
Hole for each terminal for connecting test probes (for measurements) (3BSE088180R1)

TL814K01 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
Empty slot protector for a High Integrity Module slot on the Ethernet FCI Module Termination Unit. 10 pieces per package.
 
Features and benefits

Empty slot protector for a High Integrity Module slot on the Ethernet FCI Module Termination Unit

Included with every TU860 and TU865 (3BSE088174R1)

TL813K01 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
Empty slot protector for a Signal Conditioning Module slot on the Select I/O Module Termination Unit. 10 pieces per package.
 
Features and benefits

Empty slot protector for a Signal Conditioning Module slot on the Select I/O Module Termination Unit (3BSE088173R1)

TL812K01 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
Empty slot protector for a Generic I/O Module slot on the Select I/O Module Termination Unit. 10 pieces per package.
 
Features and benefits

Empty slot protector for a Generic I/O Module slot on the Select I/O Module Termination Unit (3BSE088172R1)

TL811K01 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
Empty slot protector for a Ethernet Adapter slot on the Ethernet FCI Module Termination Unit. 10 pieces per package.
 
Features and benefits

Empty slot protector for a Ethernet Adapter slot on the Ethernet FCI Module Termination Unit (3BSE088171R1)

TL810K01 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
Empty slot protector for a Fieldbus Communication Interface slot on the Ethernet FCI Module Termination Unit. 10 pieces per package.
Features and benefits

Empty slot protector for a Fieldbus Communication Interface slot on the Ethernet FCI Module Termination Unit (3BSE088170R1)

TB861V015 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
A cluster of up to 12 I/O units can be connected to one FCI. If they are all on the same DIN rail, the I/O MTUs are connected to each other. The Modulebus then goes though the I/O MTUs.
If not all the I/O MTUs can fit on the same DIN rail, TB861 can be used to extend the Modulebus to the first I/O MTU on the next DIN rail. The outlet part is connected to the bottom of the last I/O MTU on the first DIN rail. The inlet part is connected to the top of the first I/O MTU on the second DIN rail. TB861V015 extends the Modulebus from one DIN-rail to another. Length 1.5 m.
Features and benefits

Extends the Modulebus from one DIN-rail to another. Length 1.5 m.
Available in three lengths.
DIN rail mounted. 2 locking devices (one locks outlet to DIN rail and one locks inlet to DIN rail). (3BSE088164R1)

TB861V009 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
A cluster of up to 12 I/O units can be connected to one FCI. If they are all on the same DIN rail, the I/O MTUs are connected to each other. The Modulebus then goes though the I/O MTUs.
If not all the I/O MTUs can fit on the same DIN rail, TB861 can be used to extend the Modulebus to the first I/O MTU on the next DIN rail. The outlet part is connected to the bottom of the last I/O MTU on the first DIN rail. The inlet part is connected to the top of the first I/O MTU on the second DIN rail. TB861V009 extends the Modulebus from one DIN-rail to another. Length 0.9 m.
Features and benefits

Extends the Modulebus from one DIN-rail to another. Length 0.9 m.
Available in three lengths
DIN rail mounted. 2 locking devices (one locks outlet to DIN rail and one locks inlet to DIN rail). (3BSE088163R1)

TB868

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The TB868 Modulebus Terminator is required for termination of the Modulebus at the end of each cluster. If Compact Modulebus Extensions are used between groups of I/O units, the Modulebus Terminator has to be placed at the end of the last group. The Modulebus Terminator is connected at the bottom of the last I/O MTU. One Modulebus Terminator is needed per cluster.
Features and benefits

Terminates the Modulebus.
DIN rail mounted. Locking device locks it to the DIN rail.
Locking device that locks the Modulebus Terminator to the MTU for Select I/O.
Can be used in hazardous area. (3BSE088162R1)

TUS810K01

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
The TUS810K01 Select I/O Modular Termination Unit (MTU) hosts Generic I/O modules (GIOs) and up to 16 Signal Conditioning Modules (SCMs) that completes a single I/O unit.There is self-coding on the FTBs that gets set upon the initial insertion of an SCM so that if an SCM is replaced, only the same type of SCM can be inserted. To insert another type of SCM, the coding can be reset manually. The MTU also has a coding for the GIO, so that it can only be replaced with the same type of GIO.
TUS810K01 includes the DIN-rail mountable TUS810 MTU, 16 pcs FTB810 Field Terminal Blocks, 2 pcs PTB810 Power Injection Terminal Blocks and 1 pcs TUC810 Terminal Cover.
Features and benefits

Two slots for connection of Generic I/O modules (GIO).
16 slots for connection of Signal Conditioning Modules (SCM).
Two slots for connection of Power Terminal Blocks (PTB), external 24V supply.
Two Modulebus connectors, one in and one out.
One slot for connection of a grounding bar (GTB).
DIN rail mounted. 2 locking devices to lock the MTU to the DIN rail.
Slots for screw lugs (optional, for harsh high vibration environment).
Can be used in hazardous areas.

More info

More info

× (3BSE083204R1)

AIS885

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AIS885 is an Analog Input Signal Conditioning Module (16 bit) for use in High Integrity applications (certified for SIL3) supporting 2/3/4-wire devices (1.2 amp) and HART communications.
Features and benefits

Analog input for 2-wire, 3-wire or 4-wire field devices, powered by AIS885
Signal range: 4…20 mA
Can be used in hazardous areas
Certified for Functional safety
Field power sourced from the power injection
Short circuit proof, configurable current limit 0.1 to 1.2 A
Transmitter power current limited to 25 mA (for 2-wire field devices; input current
limitation for SCM pin 2)
16 bit A/D converter resolution
Galvanic isolation
Protected against wrong wiring (±35 V) between all terminals
Hardware filter, rise time 1 ms
Software filter configurable through parameters
Diagnostics:

Loop supervision (open circuit and short circuit)
Internal hardware supervision
Communication supervision
Device malfunction low, under-range, over-range and device malfunction high
detection
Internal power supervision
Power injection supervision

LED indicators:

Status (S)
Primary (P)

Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module. (3BSE080108R1)

TL820 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
TL820 Empty Slot Protector for Power Injection Terminal Blocks. 10 pieces of TL820 per package.
 
Features and benefits

Empty Slot Protector for Power Injection Terminal Blocks
Replaces the Power Injection Terminal Block in I/O MTUs that include intrinsically safe Select I/O equipment (3BSE079085R1)

DIS850

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The DIS850 is a Digital Input Signal Conditioning Module for use in intrinsically safe applications (Zone 0) supporting 2-wire NAMUR field devices with Sequence of Events (SOE).
Features and benefits

Digital input for 2-wire field devices (NAMUR proximity switches and contacts according to EN 60947-5-6)
Can be used in hazardous areas providing IS signals up to Zone 0
Channel to channel galvanic isolation
Configurable software signal filter 0…100 ms
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision

Sequence of Events (SoE)
DIS850 supports both Normally Open (NO) and Normally Closed (NC) 24 V loops
Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module (3BSE078774R1)

AOS850

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AOS850 is an Analog Output Signal Conditioning Module (16 bit) for use in Intrinsically safe applications (Zone 0) supporting 2-wire field devices and HART communications.
Features and benefits

Analog output for 2-wire field devices
Signal range: 0…20 mA or 4…20 mA
Can be used in hazardous areas
16 bit D/A converter
Channel to channel galvanic isolation
Configurable output rise/fall times (down to 1 ms; with HART down to 20 ms)
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision

Support of HART field devices (up to HART application layer rev. 7):

HART Pass-Through
Cyclic read of up to two HART Device Variables
HART Device Validation

OSP (Output Set to Predetermined value)
Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module (3BSE078772R1)

AIS850

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AIS850 is an Analog Input Signal Conditioning Module (16bit) for use in intrinsically safe applications (Zone 0) supporting 2-wire devices and HART communications.
Features and benefits

Analog input for 2-wire field devices
Signal range: 4…20 mA and 0…20 mA
Can be used in hazardous areas providing intrinsically safe signals up to Zone 0
Transmitter power current limited to 25 mA
16 bit A/D converter resolution
Channel to channel galvanic isolation
Hardware filter, rise time 1 ms
Software filter configurable through parameters
Diagnostics:

Loop supervision (open circuit and short circuit)
Internal hardware supervision
Communication supervision
Device malfunction low, underrange, overrange and device malfunction high
detection
Internal power supervision

LED indicators:

Status (S)
Primary (P)

Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module. (3BSE078770R1)

DOS810

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The DOS810 is a Digital Output (24V / 0.6A) Signal Conditioning Module supporting 2-wire devices.
Features and benefits

Digital output for 2-wire field devices
24 V / 0.6 A current sourcing
Can be used in hazardous areas
Field power sourced from the power injection
Short circuit proof, electronically current limited to 0.6 A
Built-in inductive load suppression, free-wheeling diode
Galvanic isolation
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision
Power injection supervision

OSP (Output Set to Predetermined value)
Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal.
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance.
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning.
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module (3BSE078768R1)

DIS810

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The DIS810 is a Digital Input 24V Signal Conditioning Module supporting 2/3/4-wire devices with Sequence of Events (SOE).
Features and benefits

Digital input for 2-wire, 3-wire and externally powered 4-wire field devices
Can be used in hazardous areas
Field device power output current limited to 30 mA
Channel to channel galvanic isolation
Configurable software signal filter 0…100 ms
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision

Sequence of Events (SoE)
DIS810 supports both Normally Open (NO) and Normally Closed (NC) 24 V loops
Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module (3BSE078766R1)

AOS810

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AOS810 is an Analog Output Signal Conditioning Module (16 bit) supporting 2-wire devices and HART communication.
Features and benefits

Analog output for 2-wire field devices
Signal range: 0…20 mA or 4…20 mA
Can be used in hazardous areas
16 bit D/A converter
Channel to channel galvanic isolation
Configurable output rise/fall times (down to 1 ms; with HART down to 20 ms)Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision

Support of HART field devices (up to HART application layer rev. 7):

HART Pass-Through
Cyclic read of up to two HART Device Variables
HART Device Validation

OSP (Output Set to Predetermined value)
Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance.
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module (3BSE078764R1)

AIS810

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AIS810 is an Analog Input Signal Conditioning Module (16 bit) supporting 2/4-wire devices and HART communications.
Features and benefits

Analog input for 2-wire or external powered 4-wire field devices
Signal range: 4…20 mA and 0…20 mA
Can be used in hazardous areas
Transmitter power current limited to 30 mA
16 bit A/D converter resolution
Channel to channel galvanic isolation
Hardware filter, rise time 1ms
Software filter configurable through parameters
Protected against wrong wiring
Configurable software filter
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Device malfunction low, underrange, overrange and device malfunction high detection
Internal power supervision

Support of HART field devices (up to HART application layer revision7):

HART Pass-Through
Cyclic read of up to two HART Device Variables
HART Device Validation

Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module. (3BSE078762R1)

FTB890K01 (Spare parts)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
The FTB890 is a field terminal block with 4 screw terminals to be used with a single intrinsically safe Signal Conditioning Module. The FTB is installed on the MTU for Select I/O (TUS810) and includes a keying mechanism that is set to a certain code when an SCM is inserted for the first time to ensure only the same type of SCM can be installed in that slot. The key can be reset by removing and reinserting the FTB. (10 pieces per package).
 
Features and benefits

One slot for connection of SCM
Four screw terminals for connection of wires
Coding system with 5 coding fingers for self-learning and resettable coding of the SCM type
Can be used in hazardous areas
Hole for each terminal for connecting test probes (for measurements) (3BSE078760R1)

GIS810

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The Generic IO Module (GIO) handles the communication between Fieldbus Communication Interface (FCI) and the Signal Conditioning Modules (SCM). It communicates upstream with the FCI using Modulebus, and downstream with up to 16 SCMs. Generic I/O Module. Use as single or redundant.
Features and benefits

Distribution of process I/O data between the SCMs and the FCI
Mechanical locking slider which turns off the power supplies before removal
Supports hot swap
Mechanical keying to prevent insertion of wrong module type
Can be used in hazardous areas
LED indicators:

Status (S)
Primary (P)

Diagnostics:

Hardware error supervision
Communication supervision
Internal power supervision (3BSE078740R1)

GTB810 (Accessories)

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The GTB810 Grounding Terminal Bar has 34 screw terminals, is optionally added to the TUS810 Select I/O MTU and is used to land ground shields and spare cables.
Features and benefits

Grounding bar GTB810 is an option to the I/O unit
GTB810 is isolated and can be connected by the user to ground
Facilitates grounding of spare cores and cable shields
34 screw terminals (first and last terminal used for the grounding)
Can be used in hazardous areas (3BSE078722R1)

TU865

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
The TU865 is an Ethernet Fieldbus Communication Interface Module Termination Unit (MTU) for connection to up to 12 Select I/O MTUs and hosts single and redundant Ethernet Adapters (TC810, TC811) and Ethernet FCI Communications Interface Modules (CI845s) for reliable communications with the AC 800M controllers. The TU865 also hosts an optional High Integrity Module (HI880) for use in SIL 3 safety applications and mounting is on a vertical DIN-rail. One TL814K01 cover plate is included with every TU865.

One TL814K01 cover plate is included with every TU865.

Features and benefits

Two mounting slots for connecting single/redundant CI845 Ethernet FCI modules
Two mounting slots for connecting single/redundant Ethernet Adapters
Two connectors for connecting single/redundant 24 V power supplies
Two Modulebus connectors for connecting the I/O cluster (only Select I/O
components can be connected)
Power supply for (internally powered) field devices
A slot for an HI880 High Integrity module
Mountable on a 35 mm DIN rail

More info

More info

× (3BSE078712R1)

HI880

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
HI880 is a High Integrity Module who enables High Integrity SIL3 communication with the Select I/O.
 
Features and benefits

Shall be used with Select I/O High Integrity
Supports hot swap
Can be used in hazardous areas (3BSE078701R1)

DIS890

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The DIS890 is a Digital Input Signal Conditioning Module for use in High Integrity (certified for SIL3) and intrinsically safe applications (Zone0) supporting 2-wire NAMUR field devices with Sequence of Events (SOE).
Features and benefits

Digital input for 2-wire field devices (NAMUR proximity switches and contacts according to EN 60947-5-6)
Can be used in hazardous areas up to Zone 0
Field device power output current limited to 30 mA
Channel to channel galvanic isolation
Configurable software signal filter 0…100 ms
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision

Sequence of Events (SoE)
DIS890 supports both Normally Open (NO) and Normally Closed (NC) 24 V loops and both will confirm to SIL3
Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module
Certified for SIL3 (3BSE077763R1)

GIS880

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
GIS880 a Generic I/O Module for High Integrity. Certified for SIL3. Use as single or redundant.
Features and benefits

Distribution of process I/O data between the SCMs and the FCI
Mechanical locking slider which turns off the power supplies before removal
Supports hot swap
Mechanical keying to prevent insertion of wrong module type
Can be used in hazardous areas
Certified for SIL3
LED indicators:

Status (S)
Primary (P)

Diagnostics:

Hardware error supervision
Communication supervision
Internal power supervision (3BSE075855R1)

AIS890

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget. A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AIS890 is an Analog Input Signal Conditioning Module (16 bit) for use in High Integrity (certified for SIL3) and intrinsically safe applications (Zone 0) supporting 2-wire devices and HART communications.
Features and benefits

Analog input for 2-wire field devices
Signal range: 4…20 mA
Can be used in hazardous areas providing IS signals up to Zone 0
Certified for Functional safety
Transmitter power current limited to 25 mA
16 bit A/D converter resolution
Channel to channel galvanic isolation
Hardware filter, rise time 1ms
Software filter configurable through parameters
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Internal hardware supervision
Communication supervision
Device malfunction low, underrange, overrange and device malfunction high detection
Internal power supervision

Support of HART field devices (up to HART application layer rev. 7):

HART Pass-Through
Cyclic read of up to two HART Device Variables
HART Device Validation

Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module
Certified for SIL3 (3BSE074063R1)

DOS885

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The DOS885 is a Digital Output (24V / 3A) Signal Conditioning Module for use in High Integrity applications (certified for SIL3) supporting 2-wire devices such as solenoids, horns, beacons.
Features and benefits

Digital output for 2-wire field devices
24 V/3 A current sourcing
Can be used in hazardous areas
Certified for Functional safety
Field power sourced from the power injection
Short circuit proof, electronically current limited to 3 A
Built-in inductive load suppression, free-wheeling diode
Galvanic isolation
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision
Power injection supervision

Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal.
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance.
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning.
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module
Certified for SIL3 (3BSE074061R1)

DOS880

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The DOS880 is a Digital Output (24 V / 0.6 A) Signal Conditioning Module for use in High Integrity applications (certified for SIL3) supporting 2-wire devices.
Features and benefits

Digital output for 2-wire field devices
24 V/0.6 A current sourcing
Can be used in hazardous areas
Certified for Functional safety
Field power sourced from the power injection
Short circuit proof, electronically current limited to 0.6 A
Built-in inductive load suppression, free-wheeling diode
Galvanic isolation
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision
Power injection supervision

Single loop granularity – each SCM handles a single channel.
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal.
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance.
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning.
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module.
Certified for SIL3 (3BSE074059R1)

DIS880

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The DIS880 is a Digital Input 24V Signal Conditioning Module for use in High Integrity applications (certified for SIL3) supporting 2/3/4-wire devices with Sequence of Events (SOE).
Features and benefits

Digital input for 2-wire, 3-wire and externally powered 4-wire field devices
Can be used in hazardous areas
Field device power output current limited to 30 mA
Channel to channel galvanic isolation
Configurable software signal filter 0…100 ms
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision

Sequence of Events (SoE)
DIS880 supports both Normally Open (NO) and Normally Closed (NC) 24 V loops and both will confirm to SIL3.
Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module
Certified for SIL3 (3BSE074057R1)

AOS880

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AOS880 is an Analog Output Signal Conditioning Module (16 bit) for use in High Integrity applications (certified for SIL3) supporting 2-wire devices and HART communications.
Features and benefits

Analog output for 2-wire field devices
Signal range: 4…20 mA
Can be used in hazardous areas
Certified for Functional safety
Transmitter power current limited to 30 mA
16 bit A/D converter resolution
Channel to channel galvanic isolation
Configurable output rise/fall times (down to 1ms; with HART down to 20 ms)
Safe state shutdown (0 V) in case of internal failures or lost communication.)Protected against wrong wiring
Configurable software filter
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Internal power supervision

Support of HART field devices (up to HART application layer rev. 7):

HART Pass-Through
Cyclic read of up to two HART Device Variables
HART Device Validation

Single loop granularity – each SCM handles a single channel
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal.
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance.
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning.
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module.
Certified for SIL3 (3BSE074055R1)

AIS880

Select I/O is an Ethernet networked, single channel granular I/O system for the ABB Ability™ System 800xA automation platform. Select I/O helps decouple project tasks, minimizes the impact of late changes and supports standardization of I/O cabinetry ensuring automation projects are delivered on-time and under budget.
A Signal Conditioning Module (SCM) performs the necessary signal conditioning and powering of the connected field device for one I/O channel.
The AIS880 is an Analog Input Signal Conditioning Module (16 bit) for use in High Integrity applications (certified for SIL3) supporting 2/4-wire devices and HART communications.
Features and benefits

Analog input for 2-wire or external powered 4-wire field devices
Signal range: 4…20 mA
Can be used in hazardous areas
Certified for Functional safety
Transmitter power current limited to 30 mA
16 bit A/D converter resolution
Channel to channel galvanic isolation
Hardware filter, rise time 1ms
Software filter configurable through parameters
Protected against wrong wiring
Diagnostics:

Loop supervision (open circuit and short circuit)
Hardware error supervision
Communication supervision
Device malfunction low, underrange, overrange and device malfunction high detection
Internal power supervision

Support of HART field devices (up to HART application layer rev. 7)

HART Pass-Through
Cyclic read of up to two HART Device Variables
HART Device Validation

Single loop granularity – each SCM handles a single channel.
Supports hot swap
Mechanical locking slider which turns off field device power and/or output before removal.
Field disconnect function which can galvanically separate the field loop wiring from the SCM during commissioning and maintenance.
All SCMs have electronic current limitation
Mechanical keying to prevent insertion of wrong module type after commissioning.
24V DC powered through Modulebus
Configurable through parameters
LED indicators on the SCM indicate the operational state of the module.
Certified for SIL3. (3BSE074053R1)

DO828

The DO828 is an 16 channel 125V d.c. / 250V a.c. relay output module for the S800 I/O. The maximum output voltage is 125V d.c. / 250V a.c. and the maximum continuous output current is 2A. All outputs are individually isolated.
Each output channel consists of optical isolation barrier, output state indication LED, relay driver, relay and EMC protection components.
The relay supply voltage supervision, derived from the 12 V distributed on the ModuleBus, gives an error signal if the voltage disappears, and the Warning LED turns on. The error signal can be read through the ModuleBus. This supervision can be enabled/disabled with a parameter. 
Features and benefits

16 channels for 125V d.c. / 250V a.c. relay outputs
16 isolated channels
Output status indicators
OSP sets outputs to predetermined state uponerror detection (3BSE069055R1)

DI828

The DI828 is an 16 channel 120 V a.c/d.c. digital input module for the S800 I/O. The module has 16 digital inputs. The AC input voltage range is 77 – 130 V and the input current is 8.5 mA at 120V AC. The DC input voltage range is 75 – 130 V and the input current is 2.4 mA at 120V DC. The inputs are individually isolated.
Every input channel consists of current limiting components, EMC protection components, input state indication LED, optical isolation barrier and an analog filter. Channel 1 can be used as voltage supervision input for channels 2 – 8. Channel 16 can be used as voltage supervision input for channels 9 – 15.
If the voltage supervision is used and the voltage connected to channel 1 or 16 disappears, the channel error will be set for the channels and the Warning LED turns on. The error signal can be read from the ModuleBus.
Features and benefits

16 channels for 120 V AC/DC inputs
Individually isolated channels
Input status indicators
Signal filtering (3BSE069054R1)

DO818

The DO818 is a 32 channel 24 V digital output module for the S800 I/O. This module has 16 digital outputs. The output voltage range is 12 to 32 volt and the maximum continuous output current is 0.5 A. The outputs are protected against short circuits, over voltage and over temperature. The outputs are divided into two individually isolated groups with 16 output channels and one voltage supervision input in each group. Each output channel consists of a short circuit and over temperature protected high side driver, EMC protection components, inductive load suppression, output state indication LED and optical isolation barrier. The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read through the ModuleBus.
Features and benefits

32 channels for 24 V d.c.
2 isolated groups (RIV50V) with 16 channels and one process voltage supervision input in each group
The process voltage range is 12-32V dc (nominally 24V dc) and the maximum continuous output current is 0.5A per channel (3BSE069053R1)

DI818

This module has 32 digital inputs. The input voltage range is 18 to 30 volt d.c. and the input current is 4.3mA at 24 V. The inputs are divided into two individually isolated groups with 16 channels and one voltage supervision input in each group. Every input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier. The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read via the ModuleBus.
Features and benefits

32 channels for 24 V d.c. inputs with current sinking
Two Isolated groups of 16 channels with voltage supervision
Voltage Supervision
Signal Filtering (3BSE069052R1)

AO815

The AO815 Analog Output Module has 8 unipolar analog output channels. The module performs self-diagnostic cyclically. Module diagnostics include:

External Channel Error is reported (only reported on active channels) if the process power supply that supply voltage to output circuitry is too low, or the output current is less than the output set value and the output set value is greater than 1 mA (open circuit).
Internal Channel Error is reported if the output circuit can not give the right current value.
Module Error is reported in case of Output Transistor Error, Short Circuit, Checksum Error, Internal Power Supply Error or Watchdog error.

The module has HART pass-through functionality. Only point to point communication is supported. The output filter must be enabled on channels used for HART communication.
Features and benefits

8 channels of 4…20 mA
1 group of 8 channels isolated from ground
Analog inputs are short circuit secured to ZP or +24 V
HART pass-through communication (3BSE052605R1)

AI815

The AI815 Analog Input Module has 8 channels. The modules can be configured for voltage or current inputs. Current and voltage signals cannot be mixed on the same I/O module. The voltage and current input is able to withstand an overvoltage or undervoltage of at least 11 V d.c.
The input resistance for voltage input is greater than 10 M ohm, and the input resistance for current input is 250 ohm. The module distributes the external HART compatible transmitter supply to each channel. This adds a simple connection to distribute the supply to 2-wire or 3-wire transmitters. The transmitter power is supervised and current limited. If an external power supply is used for feeding HART transmitters, the power supply must be HART compatible.
Features and benefits

8 channels for 0…20 mA, 4…20 mA, 0…5 V or 1…5 V d.c., single ended unipolar inputs
1 group of 8 channels isolated from ground
12 Bit resolution
Current limited transmitter supply per channel
HART pass-through communication (3BSE052604R1)

AI835A

The AI835/AI835A provides 8 differential input channels for Thermocouple/mV measurements. Measurement ranges configurable per channel are: -30 mV to +75 mV linear, or TC Types B, C, E, J, K, N, R, S and T, for AI835A also D, L and U.
One of the channels (Channel 8) may be configured for “Cold Junction” (ambient) temperature measurements, thus serving as CJ-channel for Ch. 1…7. The junction temperature may be measured locally on the MTUs screw terminals, or on a connection unit distant form the device.
Alternatively, a fix junction temperature for the module may be set by the user (as parameter) or for AI835A also from the application. Channel 8 may be used in the same manner as Ch. 1…7 when no CJ-temperature measurement is needed.
Features and benefits

8 differential input channels for thermocouple/mV.
Channel 8 can be designated as the CJ-channel (4-wire Pt100 RTD)
Variety of thermocouples with the following characteristics: B, C, E, J, K, N, R, S and T for AI835A also D, L and U
15 Bit resolution (A/D)
Inputs are monitored for wire-break open-circuit (3BSE051306R1)

AO845A

The AO845/AO845A Analog Output Module for single or redundant applications has 8 unipolar analog output channels. The module performs self-diagnostic cyclically. Module diagnostics include:

External Channel Error is reported (only reported on active channels) if the process power supply that supply voltage to output circuitry is too low, or the output current is less than the output set value and the output set value > 1 mA (open circuit).
Internal Channel Error is reported if the output circuit can not give the right current value. In a redundant pair the module will be commanded to error state by the ModuleBus master.
Module Error is reported in case of Output Transistor Error, Short Circuit, Checksum Error, Internal Power Supply Error, Status Link Error, Watchdog or Wrong OSP behavior.

Features and benefits

8 channels of 4…20 mA
For single or redundant applications

1 group of 8 channels isolated from ground
Analog inputs are short circuit secured to ZP or +24 V
HART pass-through communication (3BSE045584R1)

AI830A

The AI830/AI830A RTD Input Module has 8 channels for measurement of temperature with resistive elements (RTDs). With 3-wire connections. All the RTDs must be isolated from ground.
The AI830/AI830A can be used with Pt100, Cu10, Ni100, Ni120 or resistive sensors. Linearization and conversion of the temperature to Centigrade or Fahrenheit is performed on the module.
Every channel can be individually configured. The MainsFreq parameter is used to set mains frequency filter cycle time. This will give a notch filter at the frequency specified (50 Hz or 60 Hz). 
Features and benefits

8 channels for RTD (Pt100, Cu10, Ni100 and Ni120 and resistor) inputs
3-wire connection to RTDs
14 Bit resolution
Inputs are monitored for open-circuit, shortcircuit and has a input grounded sensor (3BSE040662R1)

AI880A

The AI880A High Integrity Analog Input Module is designed for single and redundant configuration. The module has 8 current input channels. The input resistance is 250 ohm.
The module distributes the external transmitter supply to each channel. This adds a simple connection to distribute the supply to 2- or 3-wire transmitters. The transmitter power is supervised and current limited. All eight channels are isolated from the ModuleBus in one group. Power to the Module is generated from the 24 V on the ModuleBus.
The AI880A complies with the NAMUR recommendation NE43, and supports configurable over- and under range limits.
Features and benefits

8 channels for 0…20 mA, 4…20 mA, single ended unipolar inputs
Single or redundant configuration
1 group of 8 channels isolated from ground
12 bit resolution
Loop Supervised DI function
Configurable alarm limit for field power outputs
Configurable over/under range for current inputs
Current limited transmitter supply per channel
Advanced on-board diagnostics
Certified for SIL3 according to IEC 61508
Certified for Category 4 according to EN 954-1
Complies with the NAMUR recommendation NE43, and supports configurable over- and under range limits
HART pass-through communication (AI880A) (3BSE039293R1)

AO810V2

The AO810/AO810V2 Analog Output Module has 8 unipolar analog output channels. To supervise the communication to the D/A-converters the serial data is read back and verified. The opencircuit diagnostic is received during the readback. The module performs self-diagnostic cyclically. The module diagnostics includes process power supply supervision, which is reported when supply voltage to output circuitry is to low. The error is reported as a channel error. The channel diagnostic includes fault detection of the channel (only reported on active channels). The error is reported if the output current is less than the output set value and the output set value is greater than 1 mA.
Features and benefits

8 channels of 0…20 mA, 4…20 mA outputs
OSP sets outputs to predetermined state upon error detection
Analog Output is to be short circuit secured to ZP or +24 V (3BSE038415R1)

AI825

The AI825 Analog Input Module has 4 individually galvanic isolated, bipolar current/voltage inputs. Each channel can be either a voltage or current input.
The module has a direct current input that withstand up to 6.3 V and a over voltage protected current input that withstand up to +30 V d.c. The current is limited by a PTC resistor.
Power to the input stages is converted from the 24 V on the ModuleBus.
Features and benefits

4 channels individually galvanic isolated inputs for +20 mA, 0…20 mA, 4…20 mA, +10 V, 0…10 V, 2…10 V
14 Bit resolution plus sign
Input shunt resistors protected to 30 V d.c.
The input withstands HART communication (3BSE036456R1)

DI825

The DI825 is an 8 channel 125 V d.c. digital input module for the S800 I/O. The input range is 71 – 150 V and the input current is 3.0 mA at 125 V. The inputs are individually isolated.
Every input channel consists of current limiting components, EMC protection components, input state indication LED, optical isolation barrier. Channel 1 can be used as voltage supervision input for channels 2 – 4, and channel 8 can be used as voltage supervision input for channels 5 – 7.
If the voltage supervision is used and the voltage connected to channel 1 or 8 disappears, the channel error will be set for the channels and the Warning LED turns on. The error signal can be read from the ModuleBus.
Features and benefits

8 channels for 125 V d.c. inputs
Individually isolated channels
Input status indicators
Sequence of event (SOE) functionality
Signal filtering (3BSE036373R1)

DP840

The DP840 module consists of 8 identical independent channels. Each channel can be used for pulse count or frequency (speed) measurement, maximum 20 kHz. The inputs can also be read as DI signals.  Each channel has a configurable input filter. The module perform self-diagnostics cyclically. With advanced diagnostics, for single or redundant applications. Interface for NAMUR, 12 V and 24 V. The input can be read as digital input signals.
Use DP840 with Module Termination Units TU810V1, TU812V1, TU814V1, TU830V1, TU833.
Features and benefits

8 channels
The modules can be used in both single and redundant applications
Interface for NAMUR, 12 V and 24 V transducer signal levels
Each channel can be configured for pulse count or frequency measurement
The inputs can also be read as DI signals
Pulse count by accumulation in a 16 bit counter
Frequency (speed) measurement 0.5 Hz – 20 kHz
Advanced on-board diagnostics (3BSE028926R1)

AI843

The AI843 Thermocouple/mV Input Module provides 8 differential input channels for Thermocouple/mV measurements. Measurement ranges configurable per channel are: -30 mV to +75 mV linear, or TC Types B, C, E, J, K, L, N, R, S, T and U. A separate Pt100 channel is used for “Cold Junction” (ambient) temperature measurements, thus serving as CJ-channel for Ch. 1…8.  
The junction temperature may be measured locally on the MTUs screw terminals, or on a connection unit distant form the device. Alternatively, a fix junction temperature for the module may be set by the user (as parameter) or a junction temperature set by the application.
Features and benefits

8 differential input channels for thermocouple/mV
Single or redundant operation
A separate channel is used as CJ-channel (4-wire Pt100 RTD)
Variety of thermocouples with the following characteristics: B, C, E, J, K, L, N, R, S, T and U
16 Bit resolution (A/D converter)
Inputs are monitored for wire-break open-circuit

More info

More info

×

 
Signal range / linearization

Input   Type
Temperature Range

TC type B (1)
44…1820°C, 111.2…3308°F

TC type C
0…2300°C, 32…4172°F

TC type D
0…2300°C, 32…4172°F

TC type E (1)
-270…1000°C, -454…1832°F

TC type J (1)
-210…1200°C, -346…2192°F

TC type K (1)
-270…1372°C, -454…2501.6°F

TC type L
-200…900°C, -328…1652°F

TC type N (1)
-270…1300°C, -454…2372°F

TC type R (1)
-50…1768°C, -58…3214.4°F

TC type S (1)
-50…1768°C, -58…3214.4°F

TC type T (1)
-270…400°C, -454…752°F

TC type U
-200…600°C, -328…1112°F

Linear range
-30…75 mV

Pt100 RTD (for CJC) (2)
-40…100°C, -40…212°F

 
(1)Linearization per IEC 584-1 1995, and following ITS 90 requirements.
(2)Sensor Type applies to Cold Junction channel only, for the measuring of the Cold Junction Compensation temperature. (3BSE028925R1)

DO880

The DO880 is a 16 channel 24 V digital output module for single or redundant application. The maximum continuous output current per channel is 0.5 A. The outputs are current limited and protected against over temperature. Each output channel consists of a current limited and over temperature protected high side driver, EMC protection components, inductive load suppression, output state indication LED and an isolation barrier to the Modulebus.
Features and benefits

16 channels for 24 V d.c. current sourcing outputs in one isolated group
Redundant or single configuration
Loop monitoring, supervision of short and open load with configurable limits (see table Table 97).
Diagnostic of output switches without pulsing on outputs
Advanced on-board diagnostics
Output status indicators (activated/error)
Degraded mode for normally energized channels (supported from DO880 PR:G)
Current limitation at short circuit and over-temperature protection of switches
Fault tolerance of 1 (as defined in IEC 61508) for output drivers. For ND (Normally De-energized) systems, outputs can still be controlled with error on output drivers
Certified for SIL3 according to IEC 61508
Certified for Category 4 according to EN 954-1. (3BSE028602R1)

DI880

The DI880 is a 16 channel 24 V d.c. digital input module for single or redundant configuration. The input voltage range is 18 to 30 V d.c. and the input current is 7 mA at 24 V d.c. Each input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier. There is one current limited transducer power output per input. The Sequence of Event function (SOE) can collect events with a resolution of 1 ms. The event queue can contain up to 512 x 16 events. The function include a Shutter filter for suppression of unwanted events. The SOE function can report the following status in the event message – Channel value, Queue full, Synchronization jitter, Uncertain time, Shutter filter active and Channel error.
Features and benefits

16 channels for 24 V d.c. inputs with current sinking
Redundant or single configuration
1 group of 16 isolated from ground
Input status indicators
Advanced on-board diagnostics
Sequence of events (SOE)
Current limited sensor supply per channel
Certified for SIL3 according to IEC 61508
Certified for Category 4 according to EN 954-1 (3BSE028586R1)

AI845

The AI845 Analog Input Module for single or redundant applications. The module has 8 channels. Each channel can be either a voltage or current input when MTU TU844 or TU845 is used, when other MTUs are used all channels become voltage or current inputs.
The voltage and current input is able to withstand an overvoltage or undervoltage of at least 11 V d.c. The input resistance for voltage input is greater than 10 M ohm and the input resistance for current input is 250 ohm.
The module distributes the external HART compatible transmitter supply to each channel. This adds a simple connection to distribute the supply to 2-wire or 3-wire transmitters. The transmitter power is supervised and current limited.
Features and benefits

8 channels for 0…20 mA, 4…20 mA, 0…5 V or 1…5 V d.c., single ended unipolar inputs
Single or redundant operation
1 group of 8 channels isolated from ground
12 Bit resolution
Current limited transmitter supply per channel
Advanced on-board diagnostics
HART pass-through communication (3BSE023675R1)

DO802

The DO802 is an 8 channel 110 V d.c./250 V a.c. relay (NO) output module for the S800 I/O. The maximum voltage range is 250 V and the maximum continuous output current is 2 A. All outputs are individually isolated. Each output channel consists of optical isolation barrier, output state indication LED, relay driver, relay and EMC protection components.
The relay supply voltage supervision, derived from the 24 V distributed on the ModuleBus, gives a channel signal error and a module warning signal if the voltage disappears. The error signal and warning signal can be read through the ModuleBus. This supervision can be enabled/disabled with a parameter.
Features and benefits

8 channels for 110 V d.c. / 250 V a.c. relay Normally Open (NO) outputs
8 isolated channels
Process connection via detachable connectors (3BSE022364R1)

DI803

The DI803 is an 8 channel 230 V a.c./d.c. digital input module for the S800 I/O. This module has 8 digital inputs. The a.c. input voltage range is 164 – 264 volt and the input current is 7.6 mA at 230 V a.c. The d.c. input range is 175 – 275 V and the input current is 1.6 mA at 220 V. The inputs are individually isolated. Every input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier.
Features and benefits

8 channels for 230 V a.c./d.c. inputs with current sinking
Individually isolated channels
Voltage supervision of field input power
Input status indicators
Signal filtering
Process connection via detachable connectors (3BSE022362R1)

DI802

The DI802 is an 8 channel 120 V a.c./d.c. digital input module for the S800 I/O. This module has 8 digital inputs. The a.c. input voltage range is 77 – 130 volt and the input current is 10 mA at 120 V a.c. The d.c. input range is 75 – 145 V and the input current is 2.8 mA at 110 V. The inputs are individually isolated. Every input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier.

Features and benefits

8 channels for 120 V a.c./d.c. inputs with current sinking
Individually isolated channels
Voltage supervision of field input power
Input status indicators
Signal filtering
Process connection via detachable connectors (3BSE022360R1)

DO840

This module has 16 digital outputs. The maximum continuous output current per channel is 0.5 A. The outputs are current limited and protected against over temperature. The outputs are divided into two groups with eight output channels and one voltage supervision input in each group. Each output channel consists of a current limited and over temperature protected high side driver, EMC protection components, inductive load suppression, output state indication LED and optical isolation barrier.
Features and benefits

16 channels for 24 V d.c. current sourcing outputs
2 isolated groups of 8 channels with process voltage supervision
Advanced on-board diagnostics
Output status indicators
OSP sets outputs to predetermined state upon error detection
Redundant or single applications
Current limited and over-temperature protection (3BSE020838R1)

DI840

The DI840 is a 16 channel 24 V d.c. digital input module for single or redundant applications. The input voltage range is 18 to 30 V d.c. and the input current is 7 mA at 24 V d.c. Each input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier.
The transducer power is supervised and current limited; one output per two input channels. The Sequence of Event function (SOE) can collect events with a resolution of 1 ms. The event queue can contain up to 257 events. The function includes a Shutter filter for filtering out unwanted events.
Features and benefits

16 channels for 24 V d.c. inputs with current sinking
1 group of 16 isolated from ground
Input status indicators
Advanced on-board diagnostics
Sequence of events
Redundant or single applications
Transducer power distribution (3BSE020836R1)

AO801

The AO801 Analog Output Module has 8 unipolar analog output channels. The module performs selfdiagnostic cyclically. A low internal power supply sets the module in INIT state (no signal from the module).
Features and benefits

8 channels of 0…20 mA, 4…20 mA outputs
OSP sets outputs to predetermined state upon error detection
Analog Output is to be short circuit secured to ZP or +24 V
Process and power connection via detachable connectors (3BSE020514R1)

AI801

The AI801 Analog Input Module has 8 channels for current input. The current input is able to handle a short circuit to the transmitter supply at least 30 V d.c without damage.
Current limiting is performed with a PTC resistor. The input resistance of the current input is 250 ohm, PTC included.
Features and benefits

8 channels for 0…20 mA, 4…20 mA d.c., single ended unipolar inputs
1 group of 8 channels isolated from ground
12 Bit resolution
Input shunt resistors protected to 30 V by PTC resistor
Analog inputs are short circuit secured to ZP or +24 V
The input withstand HART communication
Process and power connections via detachable connectors (3BSE020512R1)

DO801

The DO801 is a 16 channel 24 V digital output module for the S800 I/O. The output voltage range is 10 to 30 volt and the maximum continuous output current is 0.5 A. The outputs are protected against short circuits, over voltage and over temperature. The outputs are in one isolated group. Each output channel consists of a short circuit and over temperature protected high side driver, EMC protection components, inductive load suppression, output state indication LED and optical isolation barrier.
Features and benefits

16 channels for 24 V d.c. current sourcing outputs
1 isolated groups of 16 channels
Output status indicators
OSP sets outputs to predetermined state upon communication error
Short-circuit protection to ground and 30 V
Over-voltage and overtemperature protection
Process and power connection via detachable connectors (3BSE020510R1)

DI801

The DI801 is a 16 channel 24 V digital input module for the S800 I/O. This module has 16 digital inputs. The input voltage range is 18 to 30 volt d.c. and the input current is 6 mA at 24 V. The inputs are in one isolated group with sixteen channels and channel number sixteen can be used for voltage supervision input in the group. Every input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier.
Features and benefits

16 channels for 24 V d.c. inputs with current sinking
1 isolated groups of 16 with voltage supervision
Input status indicators
Process and power connection via detachable connectors (3BSE020508R1)

DO815

The DO815 is a 8 channel 24 V digital output module for the S800 I/O. The output voltage range is 10 to 30 V and the maximum continuous output current is 2 A @ 24 V. The outputs are protected against short circuits, and over load. The outputs are divided into two individually isolated groups with four output channels in each group. Each output channel consists of a short circuit and over load protected high side driver with open load detection (on active signal), EMC protection components, inductive load suppression, output status indication LEDs and optical isolation barrier.
Features and benefits

8 channels for 24 V d.c. current sourcing outputs
2 isolated groups of 4 channels with under voltage detection
OSP sets outputs to predetermined state upon communication error
Output status indicators and a channel wise error flag
Short-circuit protection to ground and positive supply
Over load protection
Open load and short-circuit detection
Two output fault operation modes: Automatic reset mode and Fault latching mode
Inductive load driving capability
Filament lamp load up to 10W (3BSE013258R1)

DO821

The DO821 is an 8 channel 230 V a.c./d.c. relay (NC) output module for the S800 I/O. The maximum output voltage is 250 V a.c. and the maximum continuous output current is 3 A. All outputs are individually isolated. Each output channel consists of optical isolation barrier, output state indication LED, relay driver, relay and EMC protection components. The relay supply voltage supervision, derived from the 24 V distributed on the ModuleBus, gives an error signal if the voltage disappears, and the Warning LED turns on. The error signal can be read via the ModuleBus. This supervision can be enabled/disabled with a parameter.
Features and benefits

8 channels for 230 V a.c./d.c. relay Normal Closed (NC) outputs
8 isolated channels
Output status indicators
OSP sets outputs to predetermined state upon error detection (3BSE013250R1)

DP820

DP820 is an two-channel pulse counting module for incremental pulse transmitters up to 1.5 MHz. Each channel contains counters and registers for position/length and speed/frequency measurement. Each channel provides three balanced inputs for connection of a pulse transmitter, one digital input and one digital output. Pulse transmitters with RS422, +5 V, +12 V, +24 V and 13 mA interfaces can be connected to DP820.

Use DP820 with Module Termination Units TU810V1, TU812V1, TU814V1, TU830V1, TU833.
Features and benefits

Two channels
Interface for RS422, 5 V, 12 V, 24 V and 13 mA transducer signal levels
Simultaneous pulse count and frequency measurement
Pulse count (length/position) by accumulation in a bidirectional 29 bit counter
Frequency (speed) measurement 0.25 Hz – 1.5 MHz (3BSE013228R1)

DI831

The DI831 is a 16 channel 48 V d.c. digital input module for the S800 I/O. The input voltage range is 36 to 60 V d.c. and the input current is 4 mA at 48 V d.c.). Each input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier. The module cyclically performs self-diagnostics. Module diagnostics include:

Process power supply supervision (results in a module failure, if detected)
Event queue full
Time synchronization missing.

The input signals can be digitally filtered. The filter time can be set in the range 0 to 100 ms. This means that pulses shorter than the filter time are filtered out and pulses longer than specified filter time get through the filter.
Features and benefits

16 channels for 48 V d.c. inputs with current sinking
2 isolated groups of 8 channels with voltage supervision
Input status indicators
Sequence of event (SOE) functionality
Shutter filter (3BSE013212R1)

DI830

The DI830 is a 16 channel 24 V d.c. digital input module for the S800 I/O. The input voltage range is 18 to 30 V d.c. and the input current is 6 mA at 24 V d.c. Each input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier. The module cyclically performs self-diagnostics. Module diagnostics include:

Process power supply supervision (results in a module warning, if detected).
Event queue full.
Time synchronization missing.

The input signals can be digitally filtered. The filter time can be set in the range 0 to 100 ms. This means that pulses shorter than the filter time are filtered out and pulses longer than specified filter time get through the filter.
Features and benefits

16 channels for 24 V d.c. inputs with current sinking
2 isolated groups of 8 channels with voltage supervision
Input status indicators
Sequence of event (SOE) functionality
Shutter filter (3BSE013210R1)

DI811

This module has 16 digital inputs. The input signal voltage range is 36 to 60 volt d.c. and the input current is 4 mA at 48 V. The inputs are divided into two individually isolated groups with eight channels and one voltage supervision input in each group. Every input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier. The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read via the ModuleBus. 
Features and benefits

16 channels for 48 V d.c. inputs with current sinking
2 isolated groups of 8 with voltage supervision
Input status indicators (3BSE008552R1)

DI821

The DI821 is a 8 channel, 230 V a.c./d.c, digital input module for the S800 I/O. This module has 8 digital inputs. The ac input voltage range is 164 to 264 V and the input current is 11 mA at 230 V a.c. The d.c. input voltage range is 175 to 275 volt and the input current is 1.6 mA at 220 V d.c. The inputs are individually isolated.
Every input channel consists of current limiting components, EMC protection components, input state indication LED, optical isolation barrier and an analog filter (6 ms).
Channel 1 can be used as voltage supervision input for channels 2 – 4, and channel 8 can be used as voltage supervision input for channels 5 – 7. If the voltage connected to channel 1 or 8 disappears, the error inputs are activated and the Warning LED turns on. The error signal can be read from the ModuleBus.
Features and benefits

8 channels for 120 V a.c./d.c. inputs
Individually isolated channels
Voltage supervision of field input power
Input status indicators
Signal filtering (3BSE008550R1)

AO820

The AO820 Analog Output Module has 4 bipolar analog output channels. The choice of current or voltage output is configurable for each channel. There are separate sets of terminals for voltage and current outputs, and it is up to the user to wire outputs properly. The only differences between current or voltage channel configuration is in software settings.
To supervise the communication to the A/D-converters the output data is read back and verified. The opencircuit diagnostics are read continuously as well. The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read via the ModuleBus.
Features and benefits

4 channels of -20 mA…+20 mA, 0…20 mA, 4…20 mA or -10 V…+10 V, 0…10 V, 2…10 V outputs
Individually galvanically isolated channels
OSP sets outputs to predetermined state upon error detection.” (3BSE008546R1)

AI820

The AI820 Analog Input Module has 4 differential, bipolar current/voltage inputs. Each channel can be either a voltage or current input. The current inputs can withstand an accidental maximum normal mode 30 V d.c. connection. To protect the current input circuit against dangerous input levels, that is, by accidentally connecting a 24 V source, the resistor rating of the 250W current sense resistors is about 5 Watts. This is intended only to temporarily protect one channel at a time.
The module distributes the external transmitter supply to each channel. This adds a simple connection (with extended MTUs) to distribute the supply to external 2 wire transmitters. There is no current limiting on the transmitter power terminals.
All 4 channels are isolated from the ModuleBus in one group. Power to the input stages is converted from the 24 V on the ModuleBus.
Features and benefits

4 channels for -20…+20 mA, 0…20 mA, 4…20 mA, -10…+10 V, 0…10 V, 2…10 V, -5…+5 V, 0…5 V, 1…5 V d.c. bipolar differential inputs
One group of 4 channels isolated from ground
14 Bit resolution plus sign
Input shunt resistors protected to 30 V d.c.
The input withstand HART communication (3BSE008544R1)

AI810

The AI810 Analog Input Module has 8 channels. Each channel can be either a voltage or current input. The current input is able to handle a short circuit to the transmitter supply at least 30 V d.c without damage. Current limiting is performed with a PTC resistor. The input resistance of the current input is 250 ohm, PTC included.
The voltage input is able to withstand an over or undervoltage of at least 30 V d.c. Input resistance is 290k ohm. Transmitter supply can be connected to L1+, L1- and/or L2+, L2-.
Features and benefits

8 channels for 0…20 mA, 4…20 mA, 0…10 V or 2…10 V d.c., single ended unipolar inputs
1 group of 8 channels isolated from ground
12 Bit resolution
Input shunt resistors protected to 30 V by PTC resistor
Analog inputs are short circuit secured to ZP or +24 V
The input withstand HART communication. (3BSE008516R1)

DO820

The DO820 is an 8 channel 230 V a.c./d.c. relay (NO) output module for the S800 I/O. The maximum output voltage is 250 V a.c./d.c. and the maximum continuous output current is 3 A. All outputs are individually isolated. Each output channel consists of optical isolation barrier, output state indication LED, relay driver, relay and EMC protection components. The relay supply voltage supervision, derived from the 24 V distributed on the ModuleBus, gives an error signal if the voltage disappears, and the Warning LED turns on. The error signal can be read through the ModuleBus. This supervision can be enabled/disabled with a parameter.
Features and benefits

8 channels for 230 V a.c./d.c. relay Normal Open (NO) outputs
8 isolated channels
Output status indicators
OSP sets outputs to predetermined state upon error detection (3BSE008514R1)

DI820

This module has 8 digital inputs. The a.c. input voltage range is 77 – 130 volt and the input current is 10 mA at 120 V a.c. The d.c. input range is 75 – 145 V and the input current is 2.8 mA at 110 V. The inputs are individually isolated.
Every input channel consists of current limiting components, EMC protection components, input state indication LED, optical isolation barrier and an analog filter (6 ms). Channel 1 can be used as voltage supervision input for channels 2 – 4, and channel 8 can be used as voltage supervision input for channels 5 – 7.
If the voltage connected to channel 1 or 8 disappears, the error inputs are activated and the Warning LED turns on. The error signal can be read from the ModuleBus.
Features and benefits

8 channels for 120 V a.c./d.c. inputs
Individually isolated channels
Voltage supervision of field input power
Input status indicators
Signal filtering (3BSE008512R1)

DO810

This module has 16 digital outputs. The output voltage range is 10 to 30 volt and the maximum continuous output current is 0.5 A. The outputs are protected against short circuits, over voltage and over temperature. The outputs are divided into two individually isolated groups with eight output channels and one voltage supervision input in each group. Each output channel consists of a short circuit and over temperature protected high side driver, EMC protection components, inductive load suppression, output state indication LED and optical isolation barrier.
The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read through the ModuleBus. The outputs are current limited and protected against over temperature. If the outputs are overloaded the output current will be limited. 
Features and benefits

16 channels for 24 V d.c. current sourcing outputs
2 isolated groups of 8 channels with process voltage supervision
Output status indicators
OSP sets outputs to predetermined state upon error detection
Short-circuit protection to ground and 30 V
Over-voltage and over-temperature protection (3BSE008510R1)

DI810

This module has 16 digital inputs. The input voltage range is 18 to 30 volt d.c. and the input current is 6 mA at 24 V. The inputs are divided into two individually isolated groups with eight channels and one voltage supervision input in each group. Every input channel consists of current limiting components, EMC protection components, input state indication LED and optical isolation barrier. The process voltage supervision input give channel error signals if the voltage disappears. The error signal can be read via the ModuleBus.
Features and benefits

16 channels for 24 V d.c. inputs with current sinking
Two isolated groups of 8 with voltage supervision
Input status indicators (3BSE008508R1)

AI893

The AI893 Analog Input Module has 8 channels. The module includes Intrinsic Safety protection components on each channel for connection to process equipment in hazardous areas without the need for additional external devices.
The module can be configured for either 2 or 3-wire RTD sensors or for TC sensors. In TC mode, channel 8 be used for Cold Junction (ambient) temperature measurements, thus serving as CJ-channel for channel 1…7. The junction temperature may be measured locally on the MTUs screw terminals, or on a connection unit distant from the device. The cold junction temperature is measured with a 3-wire Pt 100 sensor. Alternatively, a fix junction temperature for the module may be set by the user (as parameter). Channel 8 may be used in the same manner as channel 1-7 when no CJ-temperature measurement is needed.
TU890 and TU891 Compact MTU can be used with this module and it enables three wire connection to the process devices without additional terminals. TU890 for Ex applications and TU891 for non Ex applications.
Features and benefits
• 8 differential input channels for 2 or 3-wire RTD and Thermocouple.
• 1 group of 8 channels isolated from ground.
• 15 Bit + sign resolution.
• Ex certified inputs. (3BSC690141R1)

AO895

The AO895 Analog Output Module has 8 channels. The module includes Intrinsic Safety protection components and HART interface on each channel for connection to process equipment in hazardous areas without the need for additional external devices.
Each channel can drive up to 20 mA loop current into a field load such as an Ex certified current-to-pressure converter and is limited to 22 mA in overload conditions. All eight channels are isolated from the ModuleBus and power supply in one group. Power to the output stages is converted from the 24 V on the power supply connections.
Features and benefits
 
• 8 channels of 4…20 mA outputs.
• HART communication.
• 1 group of 8 channels isolated from ground.
• Power to drive Ex certified I/P actuators. (3BSC690087R1)

AI895

The AI895 Analog Input Module can directly interface 2-wire transmitters and with a particular connection it can also interface 4-wire transmitters without losing the HART capability. The AI895 Analog Input Module has 8 channels. The module includes Intrinsic Safety protection components on each channel for connection to process equipment in hazardous areas without the need for additional external devices. Each channel can power and monitor a two-wire process transmitter and HART communication. The input voltage drop of the current input is typically 3 V, PTC included. The transmitter supply for each channel is able to provide at least 15 V at a 20 mA loop current to power Ex certified process transmitters and is limited to 23 mA in overload conditions.
TU890 and TU891 Compact MTU can be used with this module and it enables two wire connection to the process devices without additional terminals. TU890 for Ex applications and TU891 for non Ex applications.
 
 
Features and benefits
• 8 channels for 4…20 mA, single ended unipolar inputs.
• HART communication.
• 1 group of 8 channels isolated from ground.
• Power and monitor for Ex certified two-wire transmitters.
• Non energy-storing analog inputs for externally powered sources. (3BSC690086R1)

DO890

The module includes Intrinsic Safety protection components on each channel for connection to process equipment in hazardous areas without the need for additional external devices.
Each channel can drive a nominal current of 40 mA into a 300 ohm field load such as an Ex certified solenoid valve, alarm sounder unit or indicator lamp. Open and short circuit detection can be configured for each channel. All four channels are galvanic isolated between channels and from the ModuleBus and power supply. Power to the output stages is converted from the 24 V on the power supply connections.
TU890 and TU891 Compact MTU can be used with this module and it enables two wire connection to the process devices without additional terminals. TU890 for Ex applications and TU891 for non Ex applications.
 
Features and benefits

4 channels for 11 V, 40 mA digital outputs.
All channels fully isolated.
Power to drive Ex certified solenoid valves and alarm sounders.
Output and fault status indicators for each channel. (3BSC690074R1)

DI890

The DI890 Digital Input Module has 8 channels. The module includes Intrinsic Safety protection components on each channel for connection to process equipment in hazardous areas without the need for additional external devices. Each channel is galvanically isolated from the power supply, ground, and each other. Intrinsically safe Proximity sensors or volt-free contacts can be powered and monitored by any channel.
The Proximity sensor should conform to the NAMUR standard and line faults can be detected without any additional external components. For line faults to be detected when using volt-free contacts, external resistors should be connected in series and in parallel to enable the state of the field circuit to be sensed by the input channel. All eight channels are galvanic isolated from the ModuleBus and power supply individually. Power to the input stages is converted from the 24 V on the power supply connections. Three LEDs indicate module status Fault (Red), Run (Green) and Warning (Yellow).
TU890 and TU891 Compact MTU can be used with this module and it enables two wire connection to the process devices without additional terminals. TU890 for Ex applications and TU891 for non Ex applications.
Features and benefits

8 channels with process voltage supervision
Output status indicators
OSP sets outputs to predetermined state upon error detection
Short-circuit protection to ground and 30 V
Over-voltage and over-temperature protection
Intrinsic Safety support
NAMUR inputs
G3 compliant (3BSC690073R1)

AO890

The AO890 Analog Output Module has 8 channels. The module includes Intrinsic Safety protection components on each channel for connection to process equipment in hazardous areas without the need for additional external devices.
Each channel can drive up to 20 mA loop current into a field load such as an Ex certified current-to-pressure converter and is limited to 22 mA in overload conditions.
TU890 and TU891 Compact MTU can be used with this module and it enables two wire connection to the process devices without additional terminals. TU890 for Ex applications and TU891 for non Ex applications.
Features and benefits
•8 channels of 0…20 mA, 4…20 mA outputs.
•1 group of 8 channels isolated from ground.
•Power to drive Ex certified I/P actuators. (3BSC690072R1)

AI890

The AI890 Analog Input Module has 8 channels. The module includes Intrinsic Safety protection components on each channel for connection to process equipment in hazardous areas without the need for additional external devices.
Each channel can be either a current input or power and monitor a two-wire process transmitter. The current input is for externally powered transmitters. The input voltage drop of the current input is typically 3 V, PTC included. The transmitter supply for each channel is able to provide at least 15 V at a 20 mA loop current to power Ex certified process transmitters and is limited to 23 mA in overload conditions. All eight channels are isolated from the ModuleBus and power supply in one group. Power to the input stages is converted from the 24 V on the power supply connections.
TU890 and TU891 Compact MTU can be used with this module and it enables two wire connection to the process devices without additional terminals. TU890 for Ex applications and TU 891 for non Ex applications.
Features and benefits
• 8 channels for 0…20 mA or 4…20 mA, single ended unipolar inputs.
• 1 group of 8 channels isolated from ground.
• Power and monitor for Ex certified two-wire transmitters.
• Non energy-storing analog inputs for externally powered sources. (3BSC690071R1)

DO930N (RO6)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area. DO930N Relay Output (RO6) With 4 normally-open contacts and 2 changeover contacts.
DO930N Digital Relay Output (RO6), relay output for higher switching power.
Features and benefits
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Relay output for higher switching power
• Output configurable as NO or NC contact
• Electrical isolation between output / bus and output / power
• Electrical isolation channel to channel
• Configurable as 4 x changeover contact
• Configurable as 6 x NO contact (3BDS014114)

CI920AN (CIPBA)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area. CI920AN Communication Interface V 2.1 (CIPBA), for Fieldbus protocol PROFIBUS DP-V1 (IEC 61158). Use only CI920AN with the same firmware for redundancy for PROFIBUS DP-V1 (observe Release Notes).
Features and benefits
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Fieldbus protocol PROFIBUS DP-V1 (IEC 61158)
• Coupling of the internal CAN bus to external PROFIBUS
• HART over PROFIBUS DP-V1
• Line or media redundancy via two coupling modules
• Electrical isolation between fieldbus, power
• Diagnosis, configuration and parameterization via PROFIBUS (3BDH000692R1)

CI920AB (CIPBA-B)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
CI920AB Communication Interface V2.1 (CIPBA-B), for Fieldbus protocol PROFIBUS DP-V1 (IEC 61158). Use only CI920AB with the same firmware for redundancy for PROFIBUS DP-V1 (observe Release Notes).
Features and benefits
• ATEX Certification for installation in Zone 2
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Fieldbus protocol PROFIBUS DP-V1 (IEC 61158)
• Coupling of the internal CAN bus to external PROFIBUS DP-V1 (IEC 61158)
• HART over PROFIBUS DP-V1
• Line or media redundancy via two coupling modules
• Electrical isolation between fieldbus, power
• Diagnosis, configuration and parameterization via PROFIBUS (3BDH000691R1)

CI920AS (CIPBA-Ex)

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
CI920AS Communication Interface V 2.1 (CIPBA-Ex), for Fieldbus protocol PROFIBUS DP-V1 (IEC 61158). Use only CI920AS with the same firmware for redundancy for PROFIBUS DP-V1 (observe Release Notes).
Features and benefits
• ATEX Certification for installation in Zone 1
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Fieldbus protocol PROFIBUS DP-V1 (IEC 61158)
• Coupling of the internal CAN bus to external PROFIBUS DP-V1 (IEC 61158)
• HART over PROFIBUS DP-V1
• Line or media redundancy via two coupling modules
• Electrical isolation between fieldbus, power
• Diagnosis, configuration and parameterization via PROFIBUS (3BDH000690R1)

SA920S Power Supply

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type S. For installation in hazardous area Zone 1. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0. SA920S Power Supply for 24 V DC, for redundant termination unit TU921S (TU16R-Ex) in S900 I/O. Do not mix SA910S with SA920S for redundancy (observe Release Notes).
Features and benefits
• ATEX Certification for installation in Zone 1
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Powering of communication interfaces and I/O modules
• Hot swap capability in Zone 1
• Redundant powering
• Alarm in case of power failure (with redundancy)
• Switching On by tighten the 4 switch-on interlock screws (3BDH000602R1)

SA920B Power Supply

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type B. For installation in hazardous area Zone 2. For connecting intrinsically safe field devices installed in Zone 2, Zone 1 or Zone 0.
SA920B Power Supply for 24 V DC, for redundant termination unit TU921B (TU16R-B) in S900 I/O. Do not mix SA910B with SA920B for redundancy (observe Release Notes).
Features and benefits
• ATEX Certification for installation in Zone 2
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Powering of communication interfaces and I/O modules
• Hot swap capability in Zone 2
• Redundant powering
• Alarm in case of power failure (with redundancy)
• Switching On by tighten the 4 switch-on interlock screws (3BDH000601R1)

SA920N Power Supply

The remote S900 I/O system can be installed in non-hazardous areas or directly in Zone 1 or Zone 2 hazardous area depending on the selected system variant. S900 I/O communicates with the control system level using the PROFIBUS DP standard. The I/O system can be installed directly in the field, therefore the costs for marshalling and wiring are reduced.
The system is sturdy, error-tolerant and easy to service. Integrated disconnection mechanisms allow replacement during operation, meaning that there is no need to interrupt the primary voltage in order to exchange the power supply units.
S900 I/O type N. For installation in safe (= non-hazardous) area.
SA920N Power Supply for 24V DC, for redundant termination unit TU921N (TU16R) in S900 I/O. Do not mix SA910N with SA920N for redundancy (observe Release Notes).
Features and benefits
• Redundancy (Power and Communication)
• Hot Configuration in Run
• Hot Swap functionality
• Extended Diagnostic
• Excellent configuration and diagnostics via FDT/DTM
• G3-coating for all components
• Simplified maintenance with auto-diagnostics
• Powering of communication interfaces and I/O modules
• Hot swap capability in safe area
• Redundant powering
• Alarm in case of power failure (with redundancy) (3BDH000600R1)