منبع تغذیه ABB ای بی بی ، لیست قیمت و مشخصات فنی (ABB Power supplies & Voters)

SD854

The SD85x Power supply units are designed for high efficiency, electronic inrush current limitation, wide operational temperature range and the extraordinary small size. Lowest power losses and high lifetime expectancy delivers lowest cost of ownership. DIN-rail mounting, width 48 mm
Efficiency up to 95.6%
20% Output Power Reserves
Easy Fuse Breaking – 3 times nominal current for 12ms
Active Power Factor Correction (PFC)
Minimal Inrush Current Surge
Temperature range -25°C and +70°C (derating 12W / °C between 60°C – 70°C)
DC-OK Relay Contact
Current Sharing Feature for Parallel Use
IECEx Zone 2 and ATEX Zone 2

SD853

The SD85x Power supply units are designed for high efficiency, electronic inrush current limitation, wide operational temperature range and the extraordinary small size. Lowest power losses and high lifetime expectancy delivers lowest cost of ownership.

The SD85x series complies for use in potentially explosive atmospheres (IECEx Zone 2, ATEX Zone 2 and Class I Div 2). The SD85x series has as a build-in power reserve and can easy breaking fuses due high overload peak current capability. DIN-rail mounting, Width 39mm
Efficiency up to 95.2%
20% Output Power Reserves
Easy Fuse Breaking due to High Overload Peak Current
Active Power Factor Correction (PFC)
Minimal Inrush Current Surge
Temperature range -25°C and +70°C (derating 6W / °C between 60°C – 70°C)
DC-OK Relay Contact
Class I Div 2, IECEx Zone 2 and ATEX Zone 2

SS823 (Voter and Over Voltage Protection)

The Voting Units SS822Z, SS823 and SS832 have been specifically designed to work as a control unit within a redundant power supply configuration. The output connections from two Power Supply Units are connected to the Voting Unit.

The Voting Unit separates the redundant Power Supply Units, supervises the voltage supplied, and generates supervision signals to be connected to the power consumer. Green LED’s, mounted on the front panel of the voting unit, provide a visual indication that correct output voltage is being delivered. Simultaneously with the green LED illuminating, a voltage free contact closes the path to the corresponding “OK connector”. Voting Unit trip levels, are factory preset.

The AC 800M High Integrity and the connected S880 High Integrity I/O system (including field power) shall be supplied from a SELV or PELV power supply (e.g. SD83x) connected through the power voter SS823. The SS823 Voting Unit has double overvoltage protection circuit on input. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)
The SS823 unit is also G3 compliant

Mains Breaker kit, DIN Rail (Mains Breaker kit)

For electrical connection of ABB Power Supplies and Voters. What items to use in the kit can vary, depending on country and site specification standards. 3 fused (6.3 A) double output terminals
Kit fit for most global connection needs
DIN rail mount

SB822 (Rechargeable battery unit)

External DIN-rail mounted rechargeable battery unit for AC 800M controllers, including lithium-ion battery, 24V DC connector and connection cable TK821V020. Width=85 mm. Equivalent amount of Lithium metal=0,8g (0,03oz) Simple DIN-rail mounting
Battery back-up for AC 800M

SS832

The Voting Units SS822Z, SS823 and SS832 have been specifically designed to be employed as a control unit within a redundant power supply configuration. The output connections from two Power Supply Units are connected to the Voting Unit.

The Voting Unit separates the redundant Power Supply Units, supervises the voltage supplied, and generates supervision signals to be connected to the power consumer.

Green LED’s, mounted on the front panel of the voting unit, provide a visual indication that the correct output voltage is being delivered. Simultaneously with the green LED illuminating, a voltage free contact closes the path to the corresponding “OK connector”. Voting Unit trip levels, are factory preset. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)

SD834

The SD83x Power Supply Units are designed to meet all the applicable electrical safety data stated by the EN 50178 harmonized European Standard Publication and the additional safety and function data required by EN 61131-2 and UL 508.

The secondary output circuitry is accepted for SELV or PELV applications. They are switch-mode Power Supply Units which convert the mains voltage to 24 volts d.c. These power supplies can be utilized for non-redundant and redundant applications.

Redundant applications require diode voting units SS823 or SS832. With the type SD83x series Power Supply Units, there is no requirement for the installation of a mains filter. They provide a soft start feature; power-on of an SD83x will not trip fuses or earth-fault circuit breakers. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)
SD834 can be connected in parallel to increase output power
Both a.c. and d.c. input at SD831 and SD834
Floating DC-OK relay contact at SD834

SD833

The SD83x Power Supply Units are designed to meet all the applicable electrical safety data stated by the EN 50178 harmonized European Standard Publication and the additional safety and function data required by EN 61131-2 and UL 508.

The secondary output circuitry is accepted for SELV or PELV applications. They are switch-mode Power Supply Units which convert the mains voltage to 24 volts d.c. These power supplies can be utilized for non-redundant and redundant applications.

Redundant applications require diode voting units SS823 or SS832. With the type SD83x series Power Supply Units, there is no requirement for the installation of a mains filter. They provide a soft start feature; power-on of an SD83x will not trip fuses or earth-fault circuit breakers. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)

SD832

The SD83x Power Supply Units are designed to meet all the applicable electrical safety data stated by the EN 50178 harmonized European Standard Publication and the additional safety and function data required by EN 61131-2 and UL 508.

The secondary output circuitry is accepted for SELV or PELV applications. They are switch-mode Power Supply Units which convert the mains voltage to 24 volts d.c. These power supplies can be utilized for non-redundant and redundant applications.

Redundant applications require diode voting units SS823 or SS832. With the type SD83x series Power Supply Units, there is no requirement for the installation of a mains filter. They provide a soft start feature; power-on of an SD83x will not trip fuses or earth-fault circuit breakers. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)

SD831

The SD83x Power Supply Units are designed to meet all the applicable electrical safety data stated by the EN 50178 harmonized European Standard Publication and the additional safety and function data required by EN 61131-2 and UL 508.

The secondary output circuitry is accepted for SELV or PELV applications. They are switch-mode Power Supply Units which convert the mains voltage to 24 volts d.c. These power supplies can be utilized for non-redundant and redundant applications.

Redundant applications require diode voting units SS823 or SS832. With the type SD83x series Power Supply Units, there is no requirement for the installation of a mains filter. They provide a soft start feature; power-on of an SD83x will not trip fuses or earth-fault circuit breakers. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)
Both a.c. and d.c. input at SD831 and SD834

SS822Z

The Voting Units SS822Z, SS823 and SS832 have been specifically designed to be employed as a control unit within a redundant power supply configuration. The output connections from two Power Supply Units are connected to the Voting Unit.

The Voting Unit separates the redundant Power Supply Units, supervises the voltage supplied, and generates supervision signals to be connected to the power consumer.

Green LED’s, mounted on the front panel of the voting unit, provide a visual indication that the correct output voltage is being delivered. Simultaneously with the green LED illuminating, a voltage free contact closes the path to the corresponding “OK connector”. Voting Unit trip levels, are factory preset. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)
SS822Z is also G3 compliant

SD822Z

SD822Z, SD83x, SS822Z, SS823 and SS832 is a range of space saving power supplies intended for the AC 800M, AC 800M-eA, S800 I/O and S800-eA I/O product lines. Output current can be selected in the range of 3-20 A and the input range is wide. Relevant voters for redundant configurations are available.

The range also supports power supply configurations of the AC 800M and S800 I/O based IEC 61508-SIL2 and SIL3 rated solutions. A Mains Breaker Kit for DIN Rail is also available for our power supplies and voters. Simple DIN-rail mounting
Class I Equipment, (when connected to Protective Earth, (PE))
Over-voltage Category III for connection to primary main
TN network
Protective separation of secondary circuit from primary circuit
Accepted for SELV and PELV applications
The output of the units is protected against over current
(current limit) and over voltage (OVP)
SD822Z is also G3 compliant